Get straight answers on epoxy floor pricing in Edmonton — what drives the cost, what's included, and what you should expect from a professional installation built to last Alberta winters.
Trust signals:
Epoxy flooring ranges in price. Typical market rates start around $7.50 per square foot; however, the size of the space, concrete condition, and coating system you choose can make it cheaper or more expensive. In general, most two-car garages fall in the $3,000–$4,500 range, while larger three-car garages typically land in the $5,000–$8,000 range. When it comes to getting your garage done, it's imperative that you are educated on the expectations of what goes into pricing a garage floor.
Pricing scales with square footage. Larger spaces use product more efficiently and spread mobilization costs over more area — so the per-square-foot rate drops as the job grows. A small single-car garage will cost more per square foot than a large three-car shop, even though the total dollar amount is lower.
Most garages are more than just the floor. Vertical walls, stairs, landings, and a moisture vapour barrier system are common additions that affect the final price. All of these are quoted as separate line items so you know exactly what you're paying for.
Not all moisture barrier products are the same, and this distinction matters.
For minor moisture concerns — slabs with low-level vapour transmission that still test within acceptable limits — a lighter preventative barrier can be applied as an additional coat over the ground concrete before the base coat. It provides an added layer of protection and peace of mind without significantly increasing project cost or timeline.
For slabs with elevated moisture readings, we use a full-build moisture vapour barrier system. This is a dedicated, high-performance product that blocks up to 25 lbs of moisture vapour transmission per 1,000 square feet per 24 hours. It is not a light preventative measure — it is an engineered moisture control system. This is the appropriate solution for any slab showing meaningful moisture presence, and it extends your warranty coverage to 10 years on the barrier layer.
We test every floor with a TRAMEX moisture meter before we touch it. 85% of garage floor coating failures trace back to moisture moving up through the concrete slab. If your slab has a moisture problem and it is not properly addressed, no coating system — regardless of quality — will perform long-term.
Commercial pricing is entirely project-specific. There is no standard per-square-foot rate that applies across the board, because the variables are too significant to generalize.
What drives commercial epoxy pricing:
Every commercial project is assessed individually with a site visit. We do not quote commercial work from square footage alone.
The single biggest driver. Product, labour, and equipment costs all scale with area — but not linearly. A larger floor uses crew time and materials more efficiently, which is why the per-square-foot rate drops for bigger jobs. A 1,200 square foot shop floor costs less per square foot than a 300 square foot single-car garage, even though the total is higher.
Not all coatings are the same price. A standard epoxy base with a polyaspartic topcoat is less material-intensive than a full moisture vapour barrier system followed by a high-build topcoat. The system we recommend depends on your concrete's condition, how you use the space, and how long you want it to last — not what is cheapest to install.
Prep is where most of the cost lives. Every floor gets diamond ground to a CSP-2 surface profile — that is non-negotiable. But some floors have heavy spalling, cracks, oil contamination, or existing coatings that need removal. These require additional patching materials — such as self-leveling underlayment, rapid-set repair mortar, and moisture-tolerant patching compound — along with extra labour time. A floor in rough condition costs more to prepare, and that is reflected honestly in the quote.
One thing to know: coatings follow the contour of the slab. They do not level it. If you have a slope or low spot that needs correction, we will quote a self-leveling skim coat as a separate line item. Any installer who promises a perfectly level floor without this step is not being straight with you.
Wall coatings, stairs, and moisture barrier systems are the most common additions. They are priced separately because they involve different labour and materials. A full wall coat on a three-car garage adds meaningful cost — but it also gives you a seamless floor-to-wall finish sealed at every joint, which is the right way to do it.
Edmonton proper is standard. If the job site is in Nisku, Acheson, Fort Saskatchewan, or outside the city core, a location-of-assignment (LOA) surcharge applies. Jobs with poor vehicle access, low clearance, or significant site logistics also factor into pricing.
We visit the site, walk the floor, and provide a written quote within 24 hours. No virtual assessments for residential — we look at the actual concrete. The quote is valid for 30 days.
Before any work begins, we run a TRAMEX moisture meter reading and a Moh's scratch hardness test on your concrete. Moisture in the slab is the number one cause of coating failure in Alberta — the freeze-thaw cycle drives ground moisture upward, especially in unheated garages. We know what we are dealing with before we mix a single coat.
Every floor is mechanically ground using industrial diamond tooling to achieve a CSP-2 concrete surface profile. This creates the mechanical bond that makes coatings last years, not months. We do not acid etch. We do not hand-sand. We grind, because prep is the single biggest factor in longevity.
All cracks, spalls, and joints are patched at this stage. The apron lip is cut in and coated to ensure the coating terminates below the tire contact point — protecting the edge without bridging the joint. Expansion joints are honoured, not filled, so the floor can move with the slab as designed.
Our standard residential system is an epoxy or polyaspartic base coat, full broadcast flake, and a polyaspartic topcoat. Depending on your floor's condition and your goals, we select the right base coat for your slab — epoxy offers better self-leveling properties on older or sloped slabs; polyaspartic cures faster on straightforward installs.
Our crew runs defined roles — one mixing, one coating, one broadcasting flake — to ensure timing and consistency across the full floor. Coating chemistry is time-sensitive. Consistency across the pour matters.
Once the floor is complete, our crew conducts a final quality inspection and documents the finished installation with photos. These are logged to the job file and available to you on request. Your 10-year workmanship warranty covers adhesion failure and delamination resulting from installation error — repaired at no cost using the same or comparable system.
Polyaspartic costs more but saves time with a faster cure. Epoxy can be built thicker, making it a better base coat option for older or more damaged slabs. The main consideration is your topcoat — that is the wear coat the floor lives on. We always recommend a polyaspartic topcoat for all residential garages, as it is UV stable and has four times the elongation of epoxy, meaning it flexes with the concrete rather than cracking.
In practice, we use an epoxy base coat on any project that cannot be completed in a single day, and we always finish with a polyaspartic topcoat. Both products perform similarly in terms of durability when high-quality materials are used. For commercial work, epoxy remains the industry standard specification — particularly for high-build coat systems. The most important factor is always product quality, not epoxy versus polyaspartic marketing.
Neither system is universally better. The right choice depends on your slab and how you use the space. That is what the free in-person quote is for.
Edmonton's climate is not forgiving to floors or coatings. We get -30°C winters, wet spring thaws, road salt and calcium chloride tracked in from November through April, and a freeze-thaw cycle that moves concrete slabs. Most coating failures we see in Edmonton trace back to one of three things: moisture in the slab, inadequate surface prep, or a product that was not designed for Canadian conditions.
Every product we install has been vetted for Alberta's temperature extremes. Our systems are rated for the full range — application in a heated space in January or a cool spring morning — because Edmonton does not give you many perfect installation days if you are waiting for ideal conditions.
Our crews work across Edmonton, Sherwood Park, St. Albert, Spruce Grove, Leduc, Beaumont, Fort Saskatchewan, Stony Plain, Nisku, and Acheson. If you are in the metro, we are your local crew — not a franchise dispatched from Calgary.
One detail that matters in Alberta's climate: we honour expansion joints rather than filling them. Our coating is cut in along the joint and down the apron lip, terminating below the tire contact point. This protects the coating edge from impact and salt intrusion while allowing the slab to continue moving with the freeze-thaw cycle as it was designed to do.
Q: How much does epoxy flooring cost in Edmonton? A: Residential garage epoxy flooring starts around $7.50 per square foot, with pricing decreasing as the square footage increases. Economies of scale apply — a larger floor spreads mobilization and labour costs over more area, bringing the per-square-foot rate down. A small two-car garage can start around $3,000 for a standard flake system. A full installation on a larger 900 square foot three-car garage that includes walls and a stair-and-landing combination can reach $8,000 or more. Commercial projects are always individually assessed and quoted following a site visit.
Q: Is epoxy flooring worth it in Alberta? A: Yes — for one reason above all others: Alberta's freeze-thaw cycle degrades bare concrete over time, and a properly installed coating system protects the slab. Beyond protection, a coated garage floor is easier to clean, resistant to oil and chemical staining, and significantly more durable than paint or DIY kits. The key phrase is "properly installed" — surface prep and product quality are what separate a 10-year floor from one that peels in two.
Q: How long does epoxy floor installation take? A: Most residential garage jobs are completed in one day. Larger jobs or those requiring significant concrete remediation may take two days — we do not rush the process. Foot traffic is safe 24 hours after completion. Vehicular traffic should wait 3–4 days minimum, and longer in cooler temperatures, as cure times extend when the slab and air temperature drop.
Q: Do I need a moisture barrier for my garage floor in Edmonton? A: Possibly — and it is worth knowing before we start. 85% of coating failures trace back to moisture moving up through the concrete slab, especially in unheated or partially heated garages in Alberta. We test every floor with a TRAMEX moisture meter before we touch it. Depending on the reading, we will recommend either a preventative moisture barrier coat for minor concerns or a full high-performance moisture vapour barrier system for elevated moisture levels. The full system blocks significantly higher moisture vapour transmission and extends your warranty coverage. It is not always needed — but when it is, skipping it is a mistake.
Q: Can I get epoxy on my garage floor in winter? A: Yes, with the right conditions. We need a heated space — the slab, air temperature, and product all need to be within application range, typically above 10°C. An unheated garage in January is usually not viable unless temporary heat is running. Polyaspartic systems have a wider application temperature range than standard epoxy, which is one reason we prefer them in Edmonton's shoulder seasons. We assess conditions at the free quote.
Q: What is the difference between epoxy and polyaspartic floor coatings? A: Epoxy offers excellent build thickness and self-leveling properties, making it a strong base coat choice for older or more damaged slabs. Polyaspartic cures faster, is UV stable, and has four times the elongation of epoxy — meaning it flexes with the slab rather than cracking over time. For most residential garages in Edmonton, we use an epoxy base where needed and always finish with a polyaspartic topcoat, as it is the more durable wear surface for Alberta conditions.
⭐⭐⭐⭐⭐ — Jason M., Sherwood Park "Had our three-car garage coated last fall and I couldn't be happier. The crew showed up on time, ground the whole floor properly, and the finish looks incredible. They walked me through the moisture test before starting and recommended the vapour barrier — glad they did. Floor is still perfect after a full Alberta winter."
⭐⭐⭐⭐⭐ — Karen T., St. Albert "We got quotes from a few companies. Elite was not the cheapest, but they were the only ones who came out in person, tested the concrete, and explained exactly what they were doing and why. The difference in professionalism was obvious. The floor looks amazing and the whole process was seamless."
⭐⭐⭐⭐⭐ — Mark D., Edmonton (Windermere) "Josh and the team are the real deal. They did our garage and the shop floor at our warehouse. Both jobs were done right — you can tell they actually care about prep and not just getting in and out. Highly recommend if you want it done properly."
48 reviews · 4.8 stars on Google Read all reviews on Google →
We do not quote from photos. We visit your garage, test the concrete, and give you a written quote within 24 hours. No pressure, no commission-based sales — just an honest assessment and a fixed price.
📞 587-413-1377 📍 Edmonton, AB — serving the full metro region
.png)
